FLASHFORGE Adventurer 5M 3D Printer Review: High-Speed Precision for Beginners and Pros

The media could not be loaded. J’ai littéralement aucune compétences en machine 3d d’où l’achat de cette machine clef en main et je regrette rien ♡.Et j’adore instalation en 5 minutes, parametrage 2 et impression du petit cub rouge de test 10 min après le déballage.Elle est silencieuse pour une machine 3d (comparaison au grosse ouverte) on entend seulement les ventilateur pour le refroidissement = bruit d’un pc poussiéreux ^^.Elle a une jolie qualité de finition de pièceset un bon rendu qui peut être amélioré en diminuant la vite est autre technique (voir bateau).Les pièces qui sont changeable sont pas chères et au nombre de deux seulement ^^.Le plateau est en vente sur Amazon pour 15-20€ . Pour pouvoir enchaîner les impressions rapidement et la tête d’imprimante est aussi sur Amazon à 30€ . Donc rien avoir avec les DIY ou il faut des tonnes de pièces pour maintenir ça machine et excessivement chère .Attention la zone d’impression est de 15cm x15cm donc reste petit mais on peut couper les impressions :).En résumé, elle est pas chère et sans réglage donc parfait pour les foyers voulant une machine et bloquant sur le prix ou sur l’installation/maintenance. Et protège avec ca boite pour éviter au enfant de ce faire mal.Je vous la recommande donc à 300%.

The media could not be loaded. J’ai littéralement aucune compétences en machine 3d d’où l’achat de cette machine clef en main et je regrette rien ♡.Et j’adore instalation en 5 minutes, parametrage 2 et impression du petit cub rouge de test 10 min après le déballage.Elle est silencieuse pour une machine 3d (comparaison au grosse ouverte) on entend seulement les ventilateur pour le refroidissement = bruit d’un pc poussiéreux ^^.Elle a une jolie qualité de finition de pièceset un bon rendu qui peut être amélioré en diminuant la vite est autre technique (voir bateau).Les pièces qui sont changeable sont pas chères et au nombre de deux seulement ^^.Le plateau est en vente sur Amazon pour 15-20€ . Pour pouvoir enchaîner les impressions rapidement et la tête d’imprimante est aussi sur Amazon à 30€ . Donc rien avoir avec les DIY ou il faut des tonnes de pièces pour maintenir ça machine et excessivement chère .Attention la zone d’impression est de 15cm x15cm donc reste petit mais on peut couper les impressions :).En résumé, elle est pas chère et sans réglage donc parfait pour les foyers voulant une machine et bloquant sur le prix ou sur l’installation/maintenance. Et protège avec ca boite pour éviter au enfant de ce faire mal.Je vous la recommande donc à 300%.

The media could not be loaded. J’ai littéralement aucune compétences en machine 3d d’où l’achat de cette machine clef en main et je regrette rien ♡.Et j’adore instalation en 5 minutes, parametrage 2 et impression du petit cub rouge de test 10 min après le déballage.Elle est silencieuse pour une machine 3d (comparaison au grosse ouverte) on entend seulement les ventilateur pour le refroidissement = bruit d’un pc poussiéreux ^^.Elle a une jolie qualité de finition de pièceset un bon rendu qui peut être amélioré en diminuant la vite est autre technique (voir bateau).Les pièces qui sont changeable sont pas chères et au nombre de deux seulement ^^.Le plateau est en vente sur Amazon pour 15-20€ . Pour pouvoir enchaîner les impressions rapidement et la tête d’imprimante est aussi sur Amazon à 30€ . Donc rien avoir avec les DIY ou il faut des tonnes de pièces pour maintenir ça machine et excessivement chère .Attention la zone d’impression est de 15cm x15cm donc reste petit mais on peut couper les impressions :).En résumé, elle est pas chère et sans réglage donc parfait pour les foyers voulant une machine et bloquant sur le prix ou sur l’installation/maintenance. Et protège avec ca boite pour éviter au enfant de ce faire mal.Je vous la recommande donc à 300%.

The media could not be loaded. J’ai littéralement aucune compétences en machine 3d d’où l’achat de cette machine clef en main et je regrette rien ♡.Et j’adore instalation en 5 minutes, parametrage 2 et impression du petit cub rouge de test 10 min après le déballage.Elle est silencieuse pour une machine 3d (comparaison au grosse ouverte) on entend seulement les ventilateur pour le refroidissement = bruit d’un pc poussiéreux ^^.Elle a une jolie qualité de finition de pièceset un bon rendu qui peut être amélioré en diminuant la vite est autre technique (voir bateau).Les pièces qui sont changeable sont pas chères et au nombre de deux seulement ^^.Le plateau est en vente sur Amazon pour 15-20€ . Pour pouvoir enchaîner les impressions rapidement et la tête d’imprimante est aussi sur Amazon à 30€ . Donc rien avoir avec les DIY ou il faut des tonnes de pièces pour maintenir ça machine et excessivement chère .Attention la zone d’impression est de 15cm x15cm donc reste petit mais on peut couper les impressions :).En résumé, elle est pas chère et sans réglage donc parfait pour les foyers voulant une machine et bloquant sur le prix ou sur l’installation/maintenance. Et protège avec ca boite pour éviter au enfant de ce faire mal.Je vous la recommande donc à 300%.

The media could not be loaded. J’ai littéralement aucune compétences en machine 3d d’où l’achat de cette machine clef en main et je regrette rien ♡.Et j’adore instalation en 5 minutes, parametrage 2 et impression du petit cub rouge de test 10 min après le déballage.Elle est silencieuse pour une machine 3d (comparaison au grosse ouverte) on entend seulement les ventilateur pour le refroidissement = bruit d’un pc poussiéreux ^^.Elle a une jolie qualité de finition de pièceset un bon rendu qui peut être amélioré en diminuant la vite est autre technique (voir bateau).Les pièces qui sont changeable sont pas chères et au nombre de deux seulement ^^.Le plateau est en vente sur Amazon pour 15-20€ . Pour pouvoir enchaîner les impressions rapidement et la tête d’imprimante est aussi sur Amazon à 30€ . Donc rien avoir avec les DIY ou il faut des tonnes de pièces pour maintenir ça machine et excessivement chère .Attention la zone d’impression est de 15cm x15cm donc reste petit mais on peut couper les impressions :).En résumé, elle est pas chère et sans réglage donc parfait pour les foyers voulant une machine et bloquant sur le prix ou sur l’installation/maintenance. Et protège avec ca boite pour éviter au enfant de ce faire mal.Je vous la recommande donc à 300%.

Muy buena impresora aunque hay que conocer el producto que se adquiere. Es una impresora cerrada y sencilla centrada en la conectividad y en poder imprimir con gran facilidad sin tener que destinar tiempo en montaje, calibración y ajustes.Ahí os dejo una recopilación de mis impresiones:PROS:- Plug and play. No tardas ni 5 minutos desde que la sacas de la caja hasta que puedes comenzar a imprimir la prueba.- Buena calidad de impresión tanto en PLA como en ABS. Aunque no es super rápida, tienen una velocidad correcta.- Rápido nivelado en 9 puntos.- Es cerrada, con lo que eliminamos corrientes de aire y mejoramos la temperatura ambiental de impresión (Importante para el ABS)- Muy buena conectividad, aunque con algunos problemas en el uso.CONTRAS:- Reducido volumen de impresión: 150x150x150 mm- Solo acepta en el soporte bobinas de 250g o 500g, las cuales tienen un mayor precio/gramo, aunque se pueden encontrar fácilmente soluciones a este problema- Software cerrado de Slicing, aunque funciona muy bien y ofrece suficientes opciones de configuración- IMPORTANTE: No admite entrada por USB con la Cámara encendida, por lo que hay que apagarla en el menú de ajustes para poder añadir archivos por USB. Parece una limitación de Hardware.- Cámara tiene, pero con una calidad bastante justita. Sirve para ver que todo va bien y ya, pero por el precio que tiene es algo más que comprensible.

Muy buena impresora aunque hay que conocer el producto que se adquiere. Es una impresora cerrada y sencilla centrada en la conectividad y en poder imprimir con gran facilidad sin tener que destinar tiempo en montaje, calibración y ajustes.Ahí os dejo una recopilación de mis impresiones:PROS:- Plug and play. No tardas ni 5 minutos desde que la sacas de la caja hasta que puedes comenzar a imprimir la prueba.- Buena calidad de impresión tanto en PLA como en ABS. Aunque no es super rápida, tienen una velocidad correcta.- Rápido nivelado en 9 puntos.- Es cerrada, con lo que eliminamos corrientes de aire y mejoramos la temperatura ambiental de impresión (Importante para el ABS)- Muy buena conectividad, aunque con algunos problemas en el uso.CONTRAS:- Reducido volumen de impresión: 150x150x150 mm- Solo acepta en el soporte bobinas de 250g o 500g, las cuales tienen un mayor precio/gramo, aunque se pueden encontrar fácilmente soluciones a este problema- Software cerrado de Slicing, aunque funciona muy bien y ofrece suficientes opciones de configuración- IMPORTANTE: No admite entrada por USB con la Cámara encendida, por lo que hay que apagarla en el menú de ajustes para poder añadir archivos por USB. Parece una limitación de Hardware.- Cámara tiene, pero con una calidad bastante justita. Sirve para ver que todo va bien y ya, pero por el precio que tiene es algo más que comprensible.

Muy buena impresora aunque hay que conocer el producto que se adquiere. Es una impresora cerrada y sencilla centrada en la conectividad y en poder imprimir con gran facilidad sin tener que destinar tiempo en montaje, calibración y ajustes.Ahí os dejo una recopilación de mis impresiones:PROS:- Plug and play. No tardas ni 5 minutos desde que la sacas de la caja hasta que puedes comenzar a imprimir la prueba.- Buena calidad de impresión tanto en PLA como en ABS. Aunque no es super rápida, tienen una velocidad correcta.- Rápido nivelado en 9 puntos.- Es cerrada, con lo que eliminamos corrientes de aire y mejoramos la temperatura ambiental de impresión (Importante para el ABS)- Muy buena conectividad, aunque con algunos problemas en el uso.CONTRAS:- Reducido volumen de impresión: 150x150x150 mm- Solo acepta en el soporte bobinas de 250g o 500g, las cuales tienen un mayor precio/gramo, aunque se pueden encontrar fácilmente soluciones a este problema- Software cerrado de Slicing, aunque funciona muy bien y ofrece suficientes opciones de configuración- IMPORTANTE: No admite entrada por USB con la Cámara encendida, por lo que hay que apagarla en el menú de ajustes para poder añadir archivos por USB. Parece una limitación de Hardware.- Cámara tiene, pero con una calidad bastante justita. Sirve para ver que todo va bien y ya, pero por el precio que tiene es algo más que comprensible.

Muy buena impresora aunque hay que conocer el producto que se adquiere. Es una impresora cerrada y sencilla centrada en la conectividad y en poder imprimir con gran facilidad sin tener que destinar tiempo en montaje, calibración y ajustes.Ahí os dejo una recopilación de mis impresiones:PROS:- Plug and play. No tardas ni 5 minutos desde que la sacas de la caja hasta que puedes comenzar a imprimir la prueba.- Buena calidad de impresión tanto en PLA como en ABS. Aunque no es super rápida, tienen una velocidad correcta.- Rápido nivelado en 9 puntos.- Es cerrada, con lo que eliminamos corrientes de aire y mejoramos la temperatura ambiental de impresión (Importante para el ABS)- Muy buena conectividad, aunque con algunos problemas en el uso.CONTRAS:- Reducido volumen de impresión: 150x150x150 mm- Solo acepta en el soporte bobinas de 250g o 500g, las cuales tienen un mayor precio/gramo, aunque se pueden encontrar fácilmente soluciones a este problema- Software cerrado de Slicing, aunque funciona muy bien y ofrece suficientes opciones de configuración- IMPORTANTE: No admite entrada por USB con la Cámara encendida, por lo que hay que apagarla en el menú de ajustes para poder añadir archivos por USB. Parece una limitación de Hardware.- Cámara tiene, pero con una calidad bastante justita. Sirve para ver que todo va bien y ya, pero por el precio que tiene es algo más que comprensible.

Muy buena impresora aunque hay que conocer el producto que se adquiere. Es una impresora cerrada y sencilla centrada en la conectividad y en poder imprimir con gran facilidad sin tener que destinar tiempo en montaje, calibración y ajustes.Ahí os dejo una recopilación de mis impresiones:PROS:- Plug and play. No tardas ni 5 minutos desde que la sacas de la caja hasta que puedes comenzar a imprimir la prueba.- Buena calidad de impresión tanto en PLA como en ABS. Aunque no es super rápida, tienen una velocidad correcta.- Rápido nivelado en 9 puntos.- Es cerrada, con lo que eliminamos corrientes de aire y mejoramos la temperatura ambiental de impresión (Importante para el ABS)- Muy buena conectividad, aunque con algunos problemas en el uso.CONTRAS:- Reducido volumen de impresión: 150x150x150 mm- Solo acepta en el soporte bobinas de 250g o 500g, las cuales tienen un mayor precio/gramo, aunque se pueden encontrar fácilmente soluciones a este problema- Software cerrado de Slicing, aunque funciona muy bien y ofrece suficientes opciones de configuración- IMPORTANTE: No admite entrada por USB con la Cámara encendida, por lo que hay que apagarla en el menú de ajustes para poder añadir archivos por USB. Parece una limitación de Hardware.- Cámara tiene, pero con una calidad bastante justita. Sirve para ver que todo va bien y ya, pero por el precio que tiene es algo más que comprensible.

The media could not be loaded. This is my first venture into 3D printing and thanks to the Flashforge Adventurer 3 i am well and truly hooked!My brother is massively into 3D printing and i have asked him to print me some items in the past, he suggested i looked at buying myself one, but to be honest, whilst i am very good at new tech, 3D printing looked way too complicated for even me!Whilst browsing the Amazon daily deals i came across this printer, reading the reviews and watching a few online videos everyone seemed to be saying this device required very little knowledge and just kind of worked straight out of the box – i decided to take the plunge and ordered!When the printer arrived i was immediately super impressed by the build quality of the device and the super smart appearance of the machine. I looked at the instructions included and to be honest they were beyond pointless! I therefore watched a setup video online and hooked up the device. To my amazement it really was just plug and play! I had to download the flashprint 5 software which is free from the manufacturers website – again there is no real instructions on how to use this software but online videos helped me through it and it actually was pretty simple!The printer comes with a small test roll of 250g PLA filament in red. Loading the filament was super easy, just place the roll inside the machine, feed the end into the printer and use the touch screen to pull the filament through. The touch screen guides you through the whole process.I was now ready for my first 3D print – Super Excited! I downloaded a couple of free .STL files and loaded them into Flashprint, clicked a couple of buttons and it send the file to the printer. The display on the printer sprung to life and informed me it was receiving the file, it then displayed a nice 3D image of the item i was printing – which was a Benchy (tug boat). The print took around 1hr 30 mins but WOW – how good did this little boat look!!! That’s it i was hooked!! I ordered some more filament in black from Amazon and my next project was a skull that could hold pens/pencils. That has now been printing for around 8hrs and has around 3hrs left – so yes it’s not a fast process – the machine takes it time, but the detail is just so amazing!What i love about the machine is that it is super quiet, it does not smell when printing, the print area is fully enclosed, touch screen is great, footprint is nice and compact, internal lights make checking on your print really easy, heat up time is astonishingly fast! Biggest plus is that it really is plug and play with no 3D printing knowledge needed!What i didn’t like so much about the machine was, camera is pretty poor quality – you also can not view this in the slicing software but instead have to go to the printers IP address to view – it’s good enough for you to check on your print but it’s quite dark and lacking in detail, the quality looks like VGA rather than 720p. The printer can also only house 500g reels of filament, which are not value for money compared to larger 1kg rolls, however you can easily solve this buy purchasing a filament holder and having your PLA on the outside of the machine. The print bed is fairly small allowing a max of 150mmx150mmx150mm prints – but for a beginners machine i feel that size print is fine for an introduction into the world of 3D printing.In summary, if you are looking at getting into 3D printing then i very highly recommend you look at investing in the Flashforge Adventurer 3 machine – you honestly can not go wrong with this smart looking device! It is truly is ideal for a novice/beginner who has extremely limited knowledge of this daunting hobby. If you are a more experienced 3D printer then you may want to look elsewhere as this machine is pretty locked down in terms of firmware and customisation options.A truly amazing 3D Printer – i am totally in love with this device! I know for a fact i will be upgrading in the future and getting another machine that can perhaps print a little faster and have a larger print area. I will definitely consider getting another larger flashforge printer as i am super impressed with their product.I can not recommend this enough!!! Over the Moon with it!I hope that you found my review helpful

The media could not be loaded. This is my first venture into 3D printing and thanks to the Flashforge Adventurer 3 i am well and truly hooked!My brother is massively into 3D printing and i have asked him to print me some items in the past, he suggested i looked at buying myself one, but to be honest, whilst i am very good at new tech, 3D printing looked way too complicated for even me!Whilst browsing the Amazon daily deals i came across this printer, reading the reviews and watching a few online videos everyone seemed to be saying this device required very little knowledge and just kind of worked straight out of the box – i decided to take the plunge and ordered!When the printer arrived i was immediately super impressed by the build quality of the device and the super smart appearance of the machine. I looked at the instructions included and to be honest they were beyond pointless! I therefore watched a setup video online and hooked up the device. To my amazement it really was just plug and play! I had to download the flashprint 5 software which is free from the manufacturers website – again there is no real instructions on how to use this software but online videos helped me through it and it actually was pretty simple!The printer comes with a small test roll of 250g PLA filament in red. Loading the filament was super easy, just place the roll inside the machine, feed the end into the printer and use the touch screen to pull the filament through. The touch screen guides you through the whole process.I was now ready for my first 3D print – Super Excited! I downloaded a couple of free .STL files and loaded them into Flashprint, clicked a couple of buttons and it send the file to the printer. The display on the printer sprung to life and informed me it was receiving the file, it then displayed a nice 3D image of the item i was printing – which was a Benchy (tug boat). The print took around 1hr 30 mins but WOW – how good did this little boat look!!! That’s it i was hooked!! I ordered some more filament in black from Amazon and my next project was a skull that could hold pens/pencils. That has now been printing for around 8hrs and has around 3hrs left – so yes it’s not a fast process – the machine takes it time, but the detail is just so amazing!What i love about the machine is that it is super quiet, it does not smell when printing, the print area is fully enclosed, touch screen is great, footprint is nice and compact, internal lights make checking on your print really easy, heat up time is astonishingly fast! Biggest plus is that it really is plug and play with no 3D printing knowledge needed!What i didn’t like so much about the machine was, camera is pretty poor quality – you also can not view this in the slicing software but instead have to go to the printers IP address to view – it’s good enough for you to check on your print but it’s quite dark and lacking in detail, the quality looks like VGA rather than 720p. The printer can also only house 500g reels of filament, which are not value for money compared to larger 1kg rolls, however you can easily solve this buy purchasing a filament holder and having your PLA on the outside of the machine. The print bed is fairly small allowing a max of 150mmx150mmx150mm prints – but for a beginners machine i feel that size print is fine for an introduction into the world of 3D printing.In summary, if you are looking at getting into 3D printing then i very highly recommend you look at investing in the Flashforge Adventurer 3 machine – you honestly can not go wrong with this smart looking device! It is truly is ideal for a novice/beginner who has extremely limited knowledge of this daunting hobby. If you are a more experienced 3D printer then you may want to look elsewhere as this machine is pretty locked down in terms of firmware and customisation options.A truly amazing 3D Printer – i am totally in love with this device! I know for a fact i will be upgrading in the future and getting another machine that can perhaps print a little faster and have a larger print area. I will definitely consider getting another larger flashforge printer as i am super impressed with their product.I can not recommend this enough!!! Over the Moon with it!I hope that you found my review helpful

The media could not be loaded. This is my first venture into 3D printing and thanks to the Flashforge Adventurer 3 i am well and truly hooked!My brother is massively into 3D printing and i have asked him to print me some items in the past, he suggested i looked at buying myself one, but to be honest, whilst i am very good at new tech, 3D printing looked way too complicated for even me!Whilst browsing the Amazon daily deals i came across this printer, reading the reviews and watching a few online videos everyone seemed to be saying this device required very little knowledge and just kind of worked straight out of the box – i decided to take the plunge and ordered!When the printer arrived i was immediately super impressed by the build quality of the device and the super smart appearance of the machine. I looked at the instructions included and to be honest they were beyond pointless! I therefore watched a setup video online and hooked up the device. To my amazement it really was just plug and play! I had to download the flashprint 5 software which is free from the manufacturers website – again there is no real instructions on how to use this software but online videos helped me through it and it actually was pretty simple!The printer comes with a small test roll of 250g PLA filament in red. Loading the filament was super easy, just place the roll inside the machine, feed the end into the printer and use the touch screen to pull the filament through. The touch screen guides you through the whole process.I was now ready for my first 3D print – Super Excited! I downloaded a couple of free .STL files and loaded them into Flashprint, clicked a couple of buttons and it send the file to the printer. The display on the printer sprung to life and informed me it was receiving the file, it then displayed a nice 3D image of the item i was printing – which was a Benchy (tug boat). The print took around 1hr 30 mins but WOW – how good did this little boat look!!! That’s it i was hooked!! I ordered some more filament in black from Amazon and my next project was a skull that could hold pens/pencils. That has now been printing for around 8hrs and has around 3hrs left – so yes it’s not a fast process – the machine takes it time, but the detail is just so amazing!What i love about the machine is that it is super quiet, it does not smell when printing, the print area is fully enclosed, touch screen is great, footprint is nice and compact, internal lights make checking on your print really easy, heat up time is astonishingly fast! Biggest plus is that it really is plug and play with no 3D printing knowledge needed!What i didn’t like so much about the machine was, camera is pretty poor quality – you also can not view this in the slicing software but instead have to go to the printers IP address to view – it’s good enough for you to check on your print but it’s quite dark and lacking in detail, the quality looks like VGA rather than 720p. The printer can also only house 500g reels of filament, which are not value for money compared to larger 1kg rolls, however you can easily solve this buy purchasing a filament holder and having your PLA on the outside of the machine. The print bed is fairly small allowing a max of 150mmx150mmx150mm prints – but for a beginners machine i feel that size print is fine for an introduction into the world of 3D printing.In summary, if you are looking at getting into 3D printing then i very highly recommend you look at investing in the Flashforge Adventurer 3 machine – you honestly can not go wrong with this smart looking device! It is truly is ideal for a novice/beginner who has extremely limited knowledge of this daunting hobby. If you are a more experienced 3D printer then you may want to look elsewhere as this machine is pretty locked down in terms of firmware and customisation options.A truly amazing 3D Printer – i am totally in love with this device! I know for a fact i will be upgrading in the future and getting another machine that can perhaps print a little faster and have a larger print area. I will definitely consider getting another larger flashforge printer as i am super impressed with their product.I can not recommend this enough!!! Over the Moon with it!I hope that you found my review helpful

The media could not be loaded. This is my first venture into 3D printing and thanks to the Flashforge Adventurer 3 i am well and truly hooked!My brother is massively into 3D printing and i have asked him to print me some items in the past, he suggested i looked at buying myself one, but to be honest, whilst i am very good at new tech, 3D printing looked way too complicated for even me!Whilst browsing the Amazon daily deals i came across this printer, reading the reviews and watching a few online videos everyone seemed to be saying this device required very little knowledge and just kind of worked straight out of the box – i decided to take the plunge and ordered!When the printer arrived i was immediately super impressed by the build quality of the device and the super smart appearance of the machine. I looked at the instructions included and to be honest they were beyond pointless! I therefore watched a setup video online and hooked up the device. To my amazement it really was just plug and play! I had to download the flashprint 5 software which is free from the manufacturers website – again there is no real instructions on how to use this software but online videos helped me through it and it actually was pretty simple!The printer comes with a small test roll of 250g PLA filament in red. Loading the filament was super easy, just place the roll inside the machine, feed the end into the printer and use the touch screen to pull the filament through. The touch screen guides you through the whole process.I was now ready for my first 3D print – Super Excited! I downloaded a couple of free .STL files and loaded them into Flashprint, clicked a couple of buttons and it send the file to the printer. The display on the printer sprung to life and informed me it was receiving the file, it then displayed a nice 3D image of the item i was printing – which was a Benchy (tug boat). The print took around 1hr 30 mins but WOW – how good did this little boat look!!! That’s it i was hooked!! I ordered some more filament in black from Amazon and my next project was a skull that could hold pens/pencils. That has now been printing for around 8hrs and has around 3hrs left – so yes it’s not a fast process – the machine takes it time, but the detail is just so amazing!What i love about the machine is that it is super quiet, it does not smell when printing, the print area is fully enclosed, touch screen is great, footprint is nice and compact, internal lights make checking on your print really easy, heat up time is astonishingly fast! Biggest plus is that it really is plug and play with no 3D printing knowledge needed!What i didn’t like so much about the machine was, camera is pretty poor quality – you also can not view this in the slicing software but instead have to go to the printers IP address to view – it’s good enough for you to check on your print but it’s quite dark and lacking in detail, the quality looks like VGA rather than 720p. The printer can also only house 500g reels of filament, which are not value for money compared to larger 1kg rolls, however you can easily solve this buy purchasing a filament holder and having your PLA on the outside of the machine. The print bed is fairly small allowing a max of 150mmx150mmx150mm prints – but for a beginners machine i feel that size print is fine for an introduction into the world of 3D printing.In summary, if you are looking at getting into 3D printing then i very highly recommend you look at investing in the Flashforge Adventurer 3 machine – you honestly can not go wrong with this smart looking device! It is truly is ideal for a novice/beginner who has extremely limited knowledge of this daunting hobby. If you are a more experienced 3D printer then you may want to look elsewhere as this machine is pretty locked down in terms of firmware and customisation options.A truly amazing 3D Printer – i am totally in love with this device! I know for a fact i will be upgrading in the future and getting another machine that can perhaps print a little faster and have a larger print area. I will definitely consider getting another larger flashforge printer as i am super impressed with their product.I can not recommend this enough!!! Over the Moon with it!I hope that you found my review helpful

The media could not be loaded. This is my first venture into 3D printing and thanks to the Flashforge Adventurer 3 i am well and truly hooked!My brother is massively into 3D printing and i have asked him to print me some items in the past, he suggested i looked at buying myself one, but to be honest, whilst i am very good at new tech, 3D printing looked way too complicated for even me!Whilst browsing the Amazon daily deals i came across this printer, reading the reviews and watching a few online videos everyone seemed to be saying this device required very little knowledge and just kind of worked straight out of the box – i decided to take the plunge and ordered!When the printer arrived i was immediately super impressed by the build quality of the device and the super smart appearance of the machine. I looked at the instructions included and to be honest they were beyond pointless! I therefore watched a setup video online and hooked up the device. To my amazement it really was just plug and play! I had to download the flashprint 5 software which is free from the manufacturers website – again there is no real instructions on how to use this software but online videos helped me through it and it actually was pretty simple!The printer comes with a small test roll of 250g PLA filament in red. Loading the filament was super easy, just place the roll inside the machine, feed the end into the printer and use the touch screen to pull the filament through. The touch screen guides you through the whole process.I was now ready for my first 3D print – Super Excited! I downloaded a couple of free .STL files and loaded them into Flashprint, clicked a couple of buttons and it send the file to the printer. The display on the printer sprung to life and informed me it was receiving the file, it then displayed a nice 3D image of the item i was printing – which was a Benchy (tug boat). The print took around 1hr 30 mins but WOW – how good did this little boat look!!! That’s it i was hooked!! I ordered some more filament in black from Amazon and my next project was a skull that could hold pens/pencils. That has now been printing for around 8hrs and has around 3hrs left – so yes it’s not a fast process – the machine takes it time, but the detail is just so amazing!What i love about the machine is that it is super quiet, it does not smell when printing, the print area is fully enclosed, touch screen is great, footprint is nice and compact, internal lights make checking on your print really easy, heat up time is astonishingly fast! Biggest plus is that it really is plug and play with no 3D printing knowledge needed!What i didn’t like so much about the machine was, camera is pretty poor quality – you also can not view this in the slicing software but instead have to go to the printers IP address to view – it’s good enough for you to check on your print but it’s quite dark and lacking in detail, the quality looks like VGA rather than 720p. The printer can also only house 500g reels of filament, which are not value for money compared to larger 1kg rolls, however you can easily solve this buy purchasing a filament holder and having your PLA on the outside of the machine. The print bed is fairly small allowing a max of 150mmx150mmx150mm prints – but for a beginners machine i feel that size print is fine for an introduction into the world of 3D printing.In summary, if you are looking at getting into 3D printing then i very highly recommend you look at investing in the Flashforge Adventurer 3 machine – you honestly can not go wrong with this smart looking device! It is truly is ideal for a novice/beginner who has extremely limited knowledge of this daunting hobby. If you are a more experienced 3D printer then you may want to look elsewhere as this machine is pretty locked down in terms of firmware and customisation options.A truly amazing 3D Printer – i am totally in love with this device! I know for a fact i will be upgrading in the future and getting another machine that can perhaps print a little faster and have a larger print area. I will definitely consider getting another larger flashforge printer as i am super impressed with their product.I can not recommend this enough!!! Over the Moon with it!I hope that you found my review helpful

Amazing printer at an amazing price, but does need some improvements; getting better though. This review is for the 5M model, not the Pro model, but they are very similar and a big plus is the ease with which this can be upgraded by the user to the Pro version. It is fully on par with similar offerings from Bambu Labs and Creality. TL;DR – There is no printer less than $600 that I would recommend. This printer is fast, extremely accurate, and trouble-free.Pros:* Blazing fast – about 4 times faster than my Ender5* Extremely accurate. This is my 4th 3D Printer and the first one that passes various tolerance tests without a lot of tweaking (not that I was ever able to fully get there with other printers). This one passed the nickel test as well as the Tolerance Coin without any tweaks at all.* Plug and play. Only unpacking and plugging in the display, followed by automatic calibration.* Absolutely perfect bed leveling and adhesion. Supposedly application of a glue stick is required for PLA, but I have zero problems across the bed. Parts do pop off at the slightest touch when done, but so far have not come loose during printing. Perhaps taller parts may have problems that required either a gluestick or another bed plate material.* Perfect configuration for OrcaSlicer which is a good choice.* LCD display is easy to read, easy to use, and intuitive.Cons:* It is very loud. Part of it has to do with the high print speed. However, some optimization of fan noise should be investigated. Every online review I have seen speaks of the noise from the motherboard cooling fan when not printing. I do not find that noise to be that bad. What is bad is the two fans for the hotend. One is to cool the hotend and the other is to cool the part when printing PLA. I suspect both the choice of fans as well as excessive shrouding by the plastic enclosure are major contributors. UPDATE: the worst of the noise is actually from the motors and/or motion. This may be part of the high-speed nature.* No wifi support except for their own slicer (which is junk). At this writing, a fork of Orca supposedly supports wifi uploading. Also missing are various Klipper Web UIs. A fix for this may also be in the mix.UPDATE: Wifi is now supported. I can send prints directly from OrcaSlicer now.General UPDATE:After owning the printer for a few months now, and 300 hours of usage, I have upgraded my rating to 5 stars. This printer at $300 to $350 is the absolute best value and extremely reliable. No fussing is necessary to get good results.Recommendations to users:1. I started having adhesion problems, and the supplied glue stick was worse than no glue stick. I heard that buffing the surface with ScotchBrite pad would fix it, and it did. No glue stick or anything is needed now. Adhesion is great with both PLA & PETG. I also bumped up the heated bed temps to 60 & 70 deg respectively.2. I found I needed to print PETG at a much higher temperature – 265 degrees in order to maintain a glossy finish (which indicates the correct temp).3. Print out the spool holder for the upgrade – it makes filament changing much easier.4. You can add a camera from Flashforge (I did, but haven’t installed it yet).5. A nice upgrade would be a 2nd spool holder (or make the upgraded one into a dual holder) to make color swapping easier. If you don’t need the run-out sensor for the 2nd color, just bypass the entire Bowden tube assembly and feed straight into the extruder.6. For color changes, add M25 to the Change Filament G-Code in OrcaSlicer, then check the Manual Filament Change box under the MultiMaterial Tab (it took me a while to figure that out) in order to prevent the printer from pausing at the start of the print when a color change is inserted.Suggestions to Flashforge:1. Fix the fan noise for the hotend and motor/motion noise. I am not sure if an upgrade can be made available to existing customers, but that would be nice if you can fix this problem.2. Incorporate Klipper WebUI into the regular firmware (that can be upgraded OTA).3. Provide replacement nozzle tips in addition to the current all-in-one nozzle. It would be nice to be able to replace this inexpensive part when needed without buying an entire new nozzle.4. To the printer screen, add the time remaining and the current layer.5. Add a filament swapping system. Even a simple two-filament system would be great.

Amazing printer at an amazing price, but does need some improvements; getting better though. This review is for the 5M model, not the Pro model, but they are very similar and a big plus is the ease with which this can be upgraded by the user to the Pro version. It is fully on par with similar offerings from Bambu Labs and Creality. TL;DR – There is no printer less than $600 that I would recommend. This printer is fast, extremely accurate, and trouble-free.Pros:* Blazing fast – about 4 times faster than my Ender5* Extremely accurate. This is my 4th 3D Printer and the first one that passes various tolerance tests without a lot of tweaking (not that I was ever able to fully get there with other printers). This one passed the nickel test as well as the Tolerance Coin without any tweaks at all.* Plug and play. Only unpacking and plugging in the display, followed by automatic calibration.* Absolutely perfect bed leveling and adhesion. Supposedly application of a glue stick is required for PLA, but I have zero problems across the bed. Parts do pop off at the slightest touch when done, but so far have not come loose during printing. Perhaps taller parts may have problems that required either a gluestick or another bed plate material.* Perfect configuration for OrcaSlicer which is a good choice.* LCD display is easy to read, easy to use, and intuitive.Cons:* It is very loud. Part of it has to do with the high print speed. However, some optimization of fan noise should be investigated. Every online review I have seen speaks of the noise from the motherboard cooling fan when not printing. I do not find that noise to be that bad. What is bad is the two fans for the hotend. One is to cool the hotend and the other is to cool the part when printing PLA. I suspect both the choice of fans as well as excessive shrouding by the plastic enclosure are major contributors. UPDATE: the worst of the noise is actually from the motors and/or motion. This may be part of the high-speed nature.* No wifi support except for their own slicer (which is junk). At this writing, a fork of Orca supposedly supports wifi uploading. Also missing are various Klipper Web UIs. A fix for this may also be in the mix.UPDATE: Wifi is now supported. I can send prints directly from OrcaSlicer now.General UPDATE:After owning the printer for a few months now, and 300 hours of usage, I have upgraded my rating to 5 stars. This printer at $300 to $350 is the absolute best value and extremely reliable. No fussing is necessary to get good results.Recommendations to users:1. I started having adhesion problems, and the supplied glue stick was worse than no glue stick. I heard that buffing the surface with ScotchBrite pad would fix it, and it did. No glue stick or anything is needed now. Adhesion is great with both PLA & PETG. I also bumped up the heated bed temps to 60 & 70 deg respectively.2. I found I needed to print PETG at a much higher temperature – 265 degrees in order to maintain a glossy finish (which indicates the correct temp).3. Print out the spool holder for the upgrade – it makes filament changing much easier.4. You can add a camera from Flashforge (I did, but haven’t installed it yet).5. A nice upgrade would be a 2nd spool holder (or make the upgraded one into a dual holder) to make color swapping easier. If you don’t need the run-out sensor for the 2nd color, just bypass the entire Bowden tube assembly and feed straight into the extruder.6. For color changes, add M25 to the Change Filament G-Code in OrcaSlicer, then check the Manual Filament Change box under the MultiMaterial Tab (it took me a while to figure that out) in order to prevent the printer from pausing at the start of the print when a color change is inserted.Suggestions to Flashforge:1. Fix the fan noise for the hotend and motor/motion noise. I am not sure if an upgrade can be made available to existing customers, but that would be nice if you can fix this problem.2. Incorporate Klipper WebUI into the regular firmware (that can be upgraded OTA).3. Provide replacement nozzle tips in addition to the current all-in-one nozzle. It would be nice to be able to replace this inexpensive part when needed without buying an entire new nozzle.4. To the printer screen, add the time remaining and the current layer.5. Add a filament swapping system. Even a simple two-filament system would be great.

Amazing printer at an amazing price, but does need some improvements; getting better though. This review is for the 5M model, not the Pro model, but they are very similar and a big plus is the ease with which this can be upgraded by the user to the Pro version. It is fully on par with similar offerings from Bambu Labs and Creality. TL;DR – There is no printer less than $600 that I would recommend. This printer is fast, extremely accurate, and trouble-free.Pros:* Blazing fast – about 4 times faster than my Ender5* Extremely accurate. This is my 4th 3D Printer and the first one that passes various tolerance tests without a lot of tweaking (not that I was ever able to fully get there with other printers). This one passed the nickel test as well as the Tolerance Coin without any tweaks at all.* Plug and play. Only unpacking and plugging in the display, followed by automatic calibration.* Absolutely perfect bed leveling and adhesion. Supposedly application of a glue stick is required for PLA, but I have zero problems across the bed. Parts do pop off at the slightest touch when done, but so far have not come loose during printing. Perhaps taller parts may have problems that required either a gluestick or another bed plate material.* Perfect configuration for OrcaSlicer which is a good choice.* LCD display is easy to read, easy to use, and intuitive.Cons:* It is very loud. Part of it has to do with the high print speed. However, some optimization of fan noise should be investigated. Every online review I have seen speaks of the noise from the motherboard cooling fan when not printing. I do not find that noise to be that bad. What is bad is the two fans for the hotend. One is to cool the hotend and the other is to cool the part when printing PLA. I suspect both the choice of fans as well as excessive shrouding by the plastic enclosure are major contributors. UPDATE: the worst of the noise is actually from the motors and/or motion. This may be part of the high-speed nature.* No wifi support except for their own slicer (which is junk). At this writing, a fork of Orca supposedly supports wifi uploading. Also missing are various Klipper Web UIs. A fix for this may also be in the mix.UPDATE: Wifi is now supported. I can send prints directly from OrcaSlicer now.General UPDATE:After owning the printer for a few months now, and 300 hours of usage, I have upgraded my rating to 5 stars. This printer at $300 to $350 is the absolute best value and extremely reliable. No fussing is necessary to get good results.Recommendations to users:1. I started having adhesion problems, and the supplied glue stick was worse than no glue stick. I heard that buffing the surface with ScotchBrite pad would fix it, and it did. No glue stick or anything is needed now. Adhesion is great with both PLA & PETG. I also bumped up the heated bed temps to 60 & 70 deg respectively.2. I found I needed to print PETG at a much higher temperature – 265 degrees in order to maintain a glossy finish (which indicates the correct temp).3. Print out the spool holder for the upgrade – it makes filament changing much easier.4. You can add a camera from Flashforge (I did, but haven’t installed it yet).5. A nice upgrade would be a 2nd spool holder (or make the upgraded one into a dual holder) to make color swapping easier. If you don’t need the run-out sensor for the 2nd color, just bypass the entire Bowden tube assembly and feed straight into the extruder.6. For color changes, add M25 to the Change Filament G-Code in OrcaSlicer, then check the Manual Filament Change box under the MultiMaterial Tab (it took me a while to figure that out) in order to prevent the printer from pausing at the start of the print when a color change is inserted.Suggestions to Flashforge:1. Fix the fan noise for the hotend and motor/motion noise. I am not sure if an upgrade can be made available to existing customers, but that would be nice if you can fix this problem.2. Incorporate Klipper WebUI into the regular firmware (that can be upgraded OTA).3. Provide replacement nozzle tips in addition to the current all-in-one nozzle. It would be nice to be able to replace this inexpensive part when needed without buying an entire new nozzle.4. To the printer screen, add the time remaining and the current layer.5. Add a filament swapping system. Even a simple two-filament system would be great.

Amazing printer at an amazing price, but does need some improvements; getting better though. This review is for the 5M model, not the Pro model, but they are very similar and a big plus is the ease with which this can be upgraded by the user to the Pro version. It is fully on par with similar offerings from Bambu Labs and Creality. TL;DR – There is no printer less than $600 that I would recommend. This printer is fast, extremely accurate, and trouble-free.Pros:* Blazing fast – about 4 times faster than my Ender5* Extremely accurate. This is my 4th 3D Printer and the first one that passes various tolerance tests without a lot of tweaking (not that I was ever able to fully get there with other printers). This one passed the nickel test as well as the Tolerance Coin without any tweaks at all.* Plug and play. Only unpacking and plugging in the display, followed by automatic calibration.* Absolutely perfect bed leveling and adhesion. Supposedly application of a glue stick is required for PLA, but I have zero problems across the bed. Parts do pop off at the slightest touch when done, but so far have not come loose during printing. Perhaps taller parts may have problems that required either a gluestick or another bed plate material.* Perfect configuration for OrcaSlicer which is a good choice.* LCD display is easy to read, easy to use, and intuitive.Cons:* It is very loud. Part of it has to do with the high print speed. However, some optimization of fan noise should be investigated. Every online review I have seen speaks of the noise from the motherboard cooling fan when not printing. I do not find that noise to be that bad. What is bad is the two fans for the hotend. One is to cool the hotend and the other is to cool the part when printing PLA. I suspect both the choice of fans as well as excessive shrouding by the plastic enclosure are major contributors. UPDATE: the worst of the noise is actually from the motors and/or motion. This may be part of the high-speed nature.* No wifi support except for their own slicer (which is junk). At this writing, a fork of Orca supposedly supports wifi uploading. Also missing are various Klipper Web UIs. A fix for this may also be in the mix.UPDATE: Wifi is now supported. I can send prints directly from OrcaSlicer now.General UPDATE:After owning the printer for a few months now, and 300 hours of usage, I have upgraded my rating to 5 stars. This printer at $300 to $350 is the absolute best value and extremely reliable. No fussing is necessary to get good results.Recommendations to users:1. I started having adhesion problems, and the supplied glue stick was worse than no glue stick. I heard that buffing the surface with ScotchBrite pad would fix it, and it did. No glue stick or anything is needed now. Adhesion is great with both PLA & PETG. I also bumped up the heated bed temps to 60 & 70 deg respectively.2. I found I needed to print PETG at a much higher temperature – 265 degrees in order to maintain a glossy finish (which indicates the correct temp).3. Print out the spool holder for the upgrade – it makes filament changing much easier.4. You can add a camera from Flashforge (I did, but haven’t installed it yet).5. A nice upgrade would be a 2nd spool holder (or make the upgraded one into a dual holder) to make color swapping easier. If you don’t need the run-out sensor for the 2nd color, just bypass the entire Bowden tube assembly and feed straight into the extruder.6. For color changes, add M25 to the Change Filament G-Code in OrcaSlicer, then check the Manual Filament Change box under the MultiMaterial Tab (it took me a while to figure that out) in order to prevent the printer from pausing at the start of the print when a color change is inserted.Suggestions to Flashforge:1. Fix the fan noise for the hotend and motor/motion noise. I am not sure if an upgrade can be made available to existing customers, but that would be nice if you can fix this problem.2. Incorporate Klipper WebUI into the regular firmware (that can be upgraded OTA).3. Provide replacement nozzle tips in addition to the current all-in-one nozzle. It would be nice to be able to replace this inexpensive part when needed without buying an entire new nozzle.4. To the printer screen, add the time remaining and the current layer.5. Add a filament swapping system. Even a simple two-filament system would be great.

Amazing printer at an amazing price, but does need some improvements; getting better though. This review is for the 5M model, not the Pro model, but they are very similar and a big plus is the ease with which this can be upgraded by the user to the Pro version. It is fully on par with similar offerings from Bambu Labs and Creality. TL;DR – There is no printer less than $600 that I would recommend. This printer is fast, extremely accurate, and trouble-free.Pros:* Blazing fast – about 4 times faster than my Ender5* Extremely accurate. This is my 4th 3D Printer and the first one that passes various tolerance tests without a lot of tweaking (not that I was ever able to fully get there with other printers). This one passed the nickel test as well as the Tolerance Coin without any tweaks at all.* Plug and play. Only unpacking and plugging in the display, followed by automatic calibration.* Absolutely perfect bed leveling and adhesion. Supposedly application of a glue stick is required for PLA, but I have zero problems across the bed. Parts do pop off at the slightest touch when done, but so far have not come loose during printing. Perhaps taller parts may have problems that required either a gluestick or another bed plate material.* Perfect configuration for OrcaSlicer which is a good choice.* LCD display is easy to read, easy to use, and intuitive.Cons:* It is very loud. Part of it has to do with the high print speed. However, some optimization of fan noise should be investigated. Every online review I have seen speaks of the noise from the motherboard cooling fan when not printing. I do not find that noise to be that bad. What is bad is the two fans for the hotend. One is to cool the hotend and the other is to cool the part when printing PLA. I suspect both the choice of fans as well as excessive shrouding by the plastic enclosure are major contributors. UPDATE: the worst of the noise is actually from the motors and/or motion. This may be part of the high-speed nature.* No wifi support except for their own slicer (which is junk). At this writing, a fork of Orca supposedly supports wifi uploading. Also missing are various Klipper Web UIs. A fix for this may also be in the mix.UPDATE: Wifi is now supported. I can send prints directly from OrcaSlicer now.General UPDATE:After owning the printer for a few months now, and 300 hours of usage, I have upgraded my rating to 5 stars. This printer at $300 to $350 is the absolute best value and extremely reliable. No fussing is necessary to get good results.Recommendations to users:1. I started having adhesion problems, and the supplied glue stick was worse than no glue stick. I heard that buffing the surface with ScotchBrite pad would fix it, and it did. No glue stick or anything is needed now. Adhesion is great with both PLA & PETG. I also bumped up the heated bed temps to 60 & 70 deg respectively.2. I found I needed to print PETG at a much higher temperature – 265 degrees in order to maintain a glossy finish (which indicates the correct temp).3. Print out the spool holder for the upgrade – it makes filament changing much easier.4. You can add a camera from Flashforge (I did, but haven’t installed it yet).5. A nice upgrade would be a 2nd spool holder (or make the upgraded one into a dual holder) to make color swapping easier. If you don’t need the run-out sensor for the 2nd color, just bypass the entire Bowden tube assembly and feed straight into the extruder.6. For color changes, add M25 to the Change Filament G-Code in OrcaSlicer, then check the Manual Filament Change box under the MultiMaterial Tab (it took me a while to figure that out) in order to prevent the printer from pausing at the start of the print when a color change is inserted.Suggestions to Flashforge:1. Fix the fan noise for the hotend and motor/motion noise. I am not sure if an upgrade can be made available to existing customers, but that would be nice if you can fix this problem.2. Incorporate Klipper WebUI into the regular firmware (that can be upgraded OTA).3. Provide replacement nozzle tips in addition to the current all-in-one nozzle. It would be nice to be able to replace this inexpensive part when needed without buying an entire new nozzle.4. To the printer screen, add the time remaining and the current layer.5. Add a filament swapping system. Even a simple two-filament system would be great.

Great printer. Software installation issues. Lengthy… I apologize.I purchased this after spending several weeks researching 3D printers. Their price points are all over the place and, as to be expected, the more features they have the more expensive they run. The initial reason for wanting a 3D printer is to make custom cutters for polymer clay. After reading dozens of reviews for different printers, I decided that this model from Flashforge would meet our needs and allow for more complicated projects in the future.It arrived the day after I ordered it (yay, Prime). Nice heavy duty box and excellent packing so it arrived in pristine condition. It is an impressive looking piece of equipment and seems to be well built. Unboxing and setup took about 30 minutes and was relatively painless. The relative part came with things that even the FlashForge website doesn’t make clear. So, I’ll have a go at it.There is a fair amount of software you need. The Flashforge website has flashy descriptions of what these do but does not really say what you need to get started.To begin with, you need FlashMaker. This is an app for iPhone, iPad, or an Android device. It is available from the app stores for the related devices. You will not be able to set up the printer without it as you have to make an account to register it and finish the setup. Once you have it, the setup is fairly straightforward and the display/touch screen on the printer guides you through the process easily. It did take a few tries to get it attached to the WiFi network but patience paid off.In the full disclosure department, we am newbies. So there was the need for a 3D application that we could use to create the projects to send to the printer. We didn’t want to spend a fortune on this and after looking at all the options, I found TinkerCAD for the iPad. It is an Autodesk product (think AutoCAD), is web based (though the is an app in the Apple App Store for the iPad that connects you to where you need to be), and it is free. Granted, I am sure if you are going for heavy engineering type 3D, you probably want a higher end application and most likely a higher end printer. I watched 3 YouTube videos on TinkerCAD and I was creating 3D objects in less than an hour. You can design directly in the app though I’ve taken another route for the time being. You’ll still need this in the process though to create the .STL files you will need later.I also learned how to create designs in Procreate on my iPad that could be exported out as PNG files. These need to be converted to .SVG files to be able to use them in TinkerCAD. There are a number of free web based conversion sites available.Then there is printing. Oh boy! Flashforge talks about a number of software applications on their website but it is very unclear what you need them for. Short answer: the .STL files from TinkerCAD need to be converted to .GX files for the printer to use. The printer comes with a thumb drive (USB A) that contains a Software folder with two applications: FlashPrint 5 and Orca-Flashforge. FlashPrint 5 is, as far as I can tell, a more consumer friendly version with fewer bells and whistles than Orca. Herein is the rub. I do almost all my graphics on my iPad and these applications require a desktop/laptop computer running either Windows, MacOS, or Linux. In my case, I have a MacBook Pro running the latest version of MacOS (Sequoia 15.0.1). Much to my surprise, the applications on the thumb drive, would not install as they were considered legacy version and not compatible with my OS. The versions on the drive were updated as of 04/28/24, which was before the latest version of the MacOS was released. I tried Flashforge’s website and had the same issue. The haven’t updated the installers for the newest version. That’s when the panic set in as I was now looking at an expensive device that I could not use.Fortunately we had an older MacBook Air that we had not updated. It is running MacOS Monterey 12.6.1. Crisis averted and I got the applications installed. I was able to import the .STL file and run the slicer to produce the .GX file for printing. If I had installed Orca, I could apparently send the file to the printer via WiFi (my next project). Using FlashPrint 5, I went old school and downloaded the .GX file to the thumb drive. The printer has a USB A port. Popped in the drive, let the printer warm up, and voila! A 3D object. By the way, the HEPA filtration system on the Pro does a great job of keeping the fumes down.Other than the software installer mess, the process was relatively painless and I must say that is it a deeply satisfying experience to handle your first 3D object.In closing, this is a very cool printer and I’d recommend it to anyone who wants a reasonably priced entry level device. Save yourself a world of frustration and make sure you have:1. Your phone or tablet with Flashmaker installed so you can setup your printer.2. A computer with the capability of installing FlashPrint 5 and/or Orca-FlashForge*3. And, of course, a 3D application capable of producing .STL files, which seem to be one of the most common types.Hope this overly long dissertation was helpful.*My guess is the MacOS version prior to Sequoia (MacOS 15) will work based on the dates on the installer files, but that is exactly what it is: a guess). I will be initiating a conversation with Flashforge about getting the installers updated.

Great printer. Software installation issues. Lengthy… I apologize.I purchased this after spending several weeks researching 3D printers. Their price points are all over the place and, as to be expected, the more features they have the more expensive they run. The initial reason for wanting a 3D printer is to make custom cutters for polymer clay. After reading dozens of reviews for different printers, I decided that this model from Flashforge would meet our needs and allow for more complicated projects in the future.It arrived the day after I ordered it (yay, Prime). Nice heavy duty box and excellent packing so it arrived in pristine condition. It is an impressive looking piece of equipment and seems to be well built. Unboxing and setup took about 30 minutes and was relatively painless. The relative part came with things that even the FlashForge website doesn’t make clear. So, I’ll have a go at it.There is a fair amount of software you need. The Flashforge website has flashy descriptions of what these do but does not really say what you need to get started.To begin with, you need FlashMaker. This is an app for iPhone, iPad, or an Android device. It is available from the app stores for the related devices. You will not be able to set up the printer without it as you have to make an account to register it and finish the setup. Once you have it, the setup is fairly straightforward and the display/touch screen on the printer guides you through the process easily. It did take a few tries to get it attached to the WiFi network but patience paid off.In the full disclosure department, we am newbies. So there was the need for a 3D application that we could use to create the projects to send to the printer. We didn’t want to spend a fortune on this and after looking at all the options, I found TinkerCAD for the iPad. It is an Autodesk product (think AutoCAD), is web based (though the is an app in the Apple App Store for the iPad that connects you to where you need to be), and it is free. Granted, I am sure if you are going for heavy engineering type 3D, you probably want a higher end application and most likely a higher end printer. I watched 3 YouTube videos on TinkerCAD and I was creating 3D objects in less than an hour. You can design directly in the app though I’ve taken another route for the time being. You’ll still need this in the process though to create the .STL files you will need later.I also learned how to create designs in Procreate on my iPad that could be exported out as PNG files. These need to be converted to .SVG files to be able to use them in TinkerCAD. There are a number of free web based conversion sites available.Then there is printing. Oh boy! Flashforge talks about a number of software applications on their website but it is very unclear what you need them for. Short answer: the .STL files from TinkerCAD need to be converted to .GX files for the printer to use. The printer comes with a thumb drive (USB A) that contains a Software folder with two applications: FlashPrint 5 and Orca-Flashforge. FlashPrint 5 is, as far as I can tell, a more consumer friendly version with fewer bells and whistles than Orca. Herein is the rub. I do almost all my graphics on my iPad and these applications require a desktop/laptop computer running either Windows, MacOS, or Linux. In my case, I have a MacBook Pro running the latest version of MacOS (Sequoia 15.0.1). Much to my surprise, the applications on the thumb drive, would not install as they were considered legacy version and not compatible with my OS. The versions on the drive were updated as of 04/28/24, which was before the latest version of the MacOS was released. I tried Flashforge’s website and had the same issue. The haven’t updated the installers for the newest version. That’s when the panic set in as I was now looking at an expensive device that I could not use.Fortunately we had an older MacBook Air that we had not updated. It is running MacOS Monterey 12.6.1. Crisis averted and I got the applications installed. I was able to import the .STL file and run the slicer to produce the .GX file for printing. If I had installed Orca, I could apparently send the file to the printer via WiFi (my next project). Using FlashPrint 5, I went old school and downloaded the .GX file to the thumb drive. The printer has a USB A port. Popped in the drive, let the printer warm up, and voila! A 3D object. By the way, the HEPA filtration system on the Pro does a great job of keeping the fumes down.Other than the software installer mess, the process was relatively painless and I must say that is it a deeply satisfying experience to handle your first 3D object.In closing, this is a very cool printer and I’d recommend it to anyone who wants a reasonably priced entry level device. Save yourself a world of frustration and make sure you have:1. Your phone or tablet with Flashmaker installed so you can setup your printer.2. A computer with the capability of installing FlashPrint 5 and/or Orca-FlashForge*3. And, of course, a 3D application capable of producing .STL files, which seem to be one of the most common types.Hope this overly long dissertation was helpful.*My guess is the MacOS version prior to Sequoia (MacOS 15) will work based on the dates on the installer files, but that is exactly what it is: a guess). I will be initiating a conversation with Flashforge about getting the installers updated.

Great printer. Software installation issues. Lengthy… I apologize.I purchased this after spending several weeks researching 3D printers. Their price points are all over the place and, as to be expected, the more features they have the more expensive they run. The initial reason for wanting a 3D printer is to make custom cutters for polymer clay. After reading dozens of reviews for different printers, I decided that this model from Flashforge would meet our needs and allow for more complicated projects in the future.It arrived the day after I ordered it (yay, Prime). Nice heavy duty box and excellent packing so it arrived in pristine condition. It is an impressive looking piece of equipment and seems to be well built. Unboxing and setup took about 30 minutes and was relatively painless. The relative part came with things that even the FlashForge website doesn’t make clear. So, I’ll have a go at it.There is a fair amount of software you need. The Flashforge website has flashy descriptions of what these do but does not really say what you need to get started.To begin with, you need FlashMaker. This is an app for iPhone, iPad, or an Android device. It is available from the app stores for the related devices. You will not be able to set up the printer without it as you have to make an account to register it and finish the setup. Once you have it, the setup is fairly straightforward and the display/touch screen on the printer guides you through the process easily. It did take a few tries to get it attached to the WiFi network but patience paid off.In the full disclosure department, we am newbies. So there was the need for a 3D application that we could use to create the projects to send to the printer. We didn’t want to spend a fortune on this and after looking at all the options, I found TinkerCAD for the iPad. It is an Autodesk product (think AutoCAD), is web based (though the is an app in the Apple App Store for the iPad that connects you to where you need to be), and it is free. Granted, I am sure if you are going for heavy engineering type 3D, you probably want a higher end application and most likely a higher end printer. I watched 3 YouTube videos on TinkerCAD and I was creating 3D objects in less than an hour. You can design directly in the app though I’ve taken another route for the time being. You’ll still need this in the process though to create the .STL files you will need later.I also learned how to create designs in Procreate on my iPad that could be exported out as PNG files. These need to be converted to .SVG files to be able to use them in TinkerCAD. There are a number of free web based conversion sites available.Then there is printing. Oh boy! Flashforge talks about a number of software applications on their website but it is very unclear what you need them for. Short answer: the .STL files from TinkerCAD need to be converted to .GX files for the printer to use. The printer comes with a thumb drive (USB A) that contains a Software folder with two applications: FlashPrint 5 and Orca-Flashforge. FlashPrint 5 is, as far as I can tell, a more consumer friendly version with fewer bells and whistles than Orca. Herein is the rub. I do almost all my graphics on my iPad and these applications require a desktop/laptop computer running either Windows, MacOS, or Linux. In my case, I have a MacBook Pro running the latest version of MacOS (Sequoia 15.0.1). Much to my surprise, the applications on the thumb drive, would not install as they were considered legacy version and not compatible with my OS. The versions on the drive were updated as of 04/28/24, which was before the latest version of the MacOS was released. I tried Flashforge’s website and had the same issue. The haven’t updated the installers for the newest version. That’s when the panic set in as I was now looking at an expensive device that I could not use.Fortunately we had an older MacBook Air that we had not updated. It is running MacOS Monterey 12.6.1. Crisis averted and I got the applications installed. I was able to import the .STL file and run the slicer to produce the .GX file for printing. If I had installed Orca, I could apparently send the file to the printer via WiFi (my next project). Using FlashPrint 5, I went old school and downloaded the .GX file to the thumb drive. The printer has a USB A port. Popped in the drive, let the printer warm up, and voila! A 3D object. By the way, the HEPA filtration system on the Pro does a great job of keeping the fumes down.Other than the software installer mess, the process was relatively painless and I must say that is it a deeply satisfying experience to handle your first 3D object.In closing, this is a very cool printer and I’d recommend it to anyone who wants a reasonably priced entry level device. Save yourself a world of frustration and make sure you have:1. Your phone or tablet with Flashmaker installed so you can setup your printer.2. A computer with the capability of installing FlashPrint 5 and/or Orca-FlashForge*3. And, of course, a 3D application capable of producing .STL files, which seem to be one of the most common types.Hope this overly long dissertation was helpful.*My guess is the MacOS version prior to Sequoia (MacOS 15) will work based on the dates on the installer files, but that is exactly what it is: a guess). I will be initiating a conversation with Flashforge about getting the installers updated.

Great printer. Software installation issues. Lengthy… I apologize.I purchased this after spending several weeks researching 3D printers. Their price points are all over the place and, as to be expected, the more features they have the more expensive they run. The initial reason for wanting a 3D printer is to make custom cutters for polymer clay. After reading dozens of reviews for different printers, I decided that this model from Flashforge would meet our needs and allow for more complicated projects in the future.It arrived the day after I ordered it (yay, Prime). Nice heavy duty box and excellent packing so it arrived in pristine condition. It is an impressive looking piece of equipment and seems to be well built. Unboxing and setup took about 30 minutes and was relatively painless. The relative part came with things that even the FlashForge website doesn’t make clear. So, I’ll have a go at it.There is a fair amount of software you need. The Flashforge website has flashy descriptions of what these do but does not really say what you need to get started.To begin with, you need FlashMaker. This is an app for iPhone, iPad, or an Android device. It is available from the app stores for the related devices. You will not be able to set up the printer without it as you have to make an account to register it and finish the setup. Once you have it, the setup is fairly straightforward and the display/touch screen on the printer guides you through the process easily. It did take a few tries to get it attached to the WiFi network but patience paid off.In the full disclosure department, we am newbies. So there was the need for a 3D application that we could use to create the projects to send to the printer. We didn’t want to spend a fortune on this and after looking at all the options, I found TinkerCAD for the iPad. It is an Autodesk product (think AutoCAD), is web based (though the is an app in the Apple App Store for the iPad that connects you to where you need to be), and it is free. Granted, I am sure if you are going for heavy engineering type 3D, you probably want a higher end application and most likely a higher end printer. I watched 3 YouTube videos on TinkerCAD and I was creating 3D objects in less than an hour. You can design directly in the app though I’ve taken another route for the time being. You’ll still need this in the process though to create the .STL files you will need later.I also learned how to create designs in Procreate on my iPad that could be exported out as PNG files. These need to be converted to .SVG files to be able to use them in TinkerCAD. There are a number of free web based conversion sites available.Then there is printing. Oh boy! Flashforge talks about a number of software applications on their website but it is very unclear what you need them for. Short answer: the .STL files from TinkerCAD need to be converted to .GX files for the printer to use. The printer comes with a thumb drive (USB A) that contains a Software folder with two applications: FlashPrint 5 and Orca-Flashforge. FlashPrint 5 is, as far as I can tell, a more consumer friendly version with fewer bells and whistles than Orca. Herein is the rub. I do almost all my graphics on my iPad and these applications require a desktop/laptop computer running either Windows, MacOS, or Linux. In my case, I have a MacBook Pro running the latest version of MacOS (Sequoia 15.0.1). Much to my surprise, the applications on the thumb drive, would not install as they were considered legacy version and not compatible with my OS. The versions on the drive were updated as of 04/28/24, which was before the latest version of the MacOS was released. I tried Flashforge’s website and had the same issue. The haven’t updated the installers for the newest version. That’s when the panic set in as I was now looking at an expensive device that I could not use.Fortunately we had an older MacBook Air that we had not updated. It is running MacOS Monterey 12.6.1. Crisis averted and I got the applications installed. I was able to import the .STL file and run the slicer to produce the .GX file for printing. If I had installed Orca, I could apparently send the file to the printer via WiFi (my next project). Using FlashPrint 5, I went old school and downloaded the .GX file to the thumb drive. The printer has a USB A port. Popped in the drive, let the printer warm up, and voila! A 3D object. By the way, the HEPA filtration system on the Pro does a great job of keeping the fumes down.Other than the software installer mess, the process was relatively painless and I must say that is it a deeply satisfying experience to handle your first 3D object.In closing, this is a very cool printer and I’d recommend it to anyone who wants a reasonably priced entry level device. Save yourself a world of frustration and make sure you have:1. Your phone or tablet with Flashmaker installed so you can setup your printer.2. A computer with the capability of installing FlashPrint 5 and/or Orca-FlashForge*3. And, of course, a 3D application capable of producing .STL files, which seem to be one of the most common types.Hope this overly long dissertation was helpful.*My guess is the MacOS version prior to Sequoia (MacOS 15) will work based on the dates on the installer files, but that is exactly what it is: a guess). I will be initiating a conversation with Flashforge about getting the installers updated.

Great printer. Software installation issues. Lengthy… I apologize.I purchased this after spending several weeks researching 3D printers. Their price points are all over the place and, as to be expected, the more features they have the more expensive they run. The initial reason for wanting a 3D printer is to make custom cutters for polymer clay. After reading dozens of reviews for different printers, I decided that this model from Flashforge would meet our needs and allow for more complicated projects in the future.It arrived the day after I ordered it (yay, Prime). Nice heavy duty box and excellent packing so it arrived in pristine condition. It is an impressive looking piece of equipment and seems to be well built. Unboxing and setup took about 30 minutes and was relatively painless. The relative part came with things that even the FlashForge website doesn’t make clear. So, I’ll have a go at it.There is a fair amount of software you need. The Flashforge website has flashy descriptions of what these do but does not really say what you need to get started.To begin with, you need FlashMaker. This is an app for iPhone, iPad, or an Android device. It is available from the app stores for the related devices. You will not be able to set up the printer without it as you have to make an account to register it and finish the setup. Once you have it, the setup is fairly straightforward and the display/touch screen on the printer guides you through the process easily. It did take a few tries to get it attached to the WiFi network but patience paid off.In the full disclosure department, we am newbies. So there was the need for a 3D application that we could use to create the projects to send to the printer. We didn’t want to spend a fortune on this and after looking at all the options, I found TinkerCAD for the iPad. It is an Autodesk product (think AutoCAD), is web based (though the is an app in the Apple App Store for the iPad that connects you to where you need to be), and it is free. Granted, I am sure if you are going for heavy engineering type 3D, you probably want a higher end application and most likely a higher end printer. I watched 3 YouTube videos on TinkerCAD and I was creating 3D objects in less than an hour. You can design directly in the app though I’ve taken another route for the time being. You’ll still need this in the process though to create the .STL files you will need later.I also learned how to create designs in Procreate on my iPad that could be exported out as PNG files. These need to be converted to .SVG files to be able to use them in TinkerCAD. There are a number of free web based conversion sites available.Then there is printing. Oh boy! Flashforge talks about a number of software applications on their website but it is very unclear what you need them for. Short answer: the .STL files from TinkerCAD need to be converted to .GX files for the printer to use. The printer comes with a thumb drive (USB A) that contains a Software folder with two applications: FlashPrint 5 and Orca-Flashforge. FlashPrint 5 is, as far as I can tell, a more consumer friendly version with fewer bells and whistles than Orca. Herein is the rub. I do almost all my graphics on my iPad and these applications require a desktop/laptop computer running either Windows, MacOS, or Linux. In my case, I have a MacBook Pro running the latest version of MacOS (Sequoia 15.0.1). Much to my surprise, the applications on the thumb drive, would not install as they were considered legacy version and not compatible with my OS. The versions on the drive were updated as of 04/28/24, which was before the latest version of the MacOS was released. I tried Flashforge’s website and had the same issue. The haven’t updated the installers for the newest version. That’s when the panic set in as I was now looking at an expensive device that I could not use.Fortunately we had an older MacBook Air that we had not updated. It is running MacOS Monterey 12.6.1. Crisis averted and I got the applications installed. I was able to import the .STL file and run the slicer to produce the .GX file for printing. If I had installed Orca, I could apparently send the file to the printer via WiFi (my next project). Using FlashPrint 5, I went old school and downloaded the .GX file to the thumb drive. The printer has a USB A port. Popped in the drive, let the printer warm up, and voila! A 3D object. By the way, the HEPA filtration system on the Pro does a great job of keeping the fumes down.Other than the software installer mess, the process was relatively painless and I must say that is it a deeply satisfying experience to handle your first 3D object.In closing, this is a very cool printer and I’d recommend it to anyone who wants a reasonably priced entry level device. Save yourself a world of frustration and make sure you have:1. Your phone or tablet with Flashmaker installed so you can setup your printer.2. A computer with the capability of installing FlashPrint 5 and/or Orca-FlashForge*3. And, of course, a 3D application capable of producing .STL files, which seem to be one of the most common types.Hope this overly long dissertation was helpful.*My guess is the MacOS version prior to Sequoia (MacOS 15) will work based on the dates on the installer files, but that is exactly what it is: a guess). I will be initiating a conversation with Flashforge about getting the installers updated.